Audi Adaptive Cruise Control Not Available: Radar Sensor Faults, Replacement and Calibration
What the ACC radar sensor does
Audi adaptive cruise control (ACC) uses a radar sensor at the front of the car to measure the distance and closing speed of the vehicle ahead. The system then brakes and accelerates to hold the gap you set. The same radar data also feeds forward collision warnings, which Audi has called braking guard and Audi pre sense front, so a radar fault usually switches those off as well.
The layout depends on the model. On the C7 A6 and A7 (about 2012–2018), including the S6, S7 and RS7, Audi used two radar sensors behind the front bumper, one on each side. In parts listings the 4G0907561 is the right-hand unit, which works as the main ACC control module, and the 4G0907541 is the left-hand unit. The 8Y A3, S3 and RS3 use a single front radar. Because each sensor has to point exactly along the car’s direction of travel, its mounting and calibration matter as much as the electronics.
Symptoms and warning messages
- ACC will not switch on, or switches off while you drive, with a message that it is unavailable.
- On the C7 A6, A7 and A8, Audi documents the message “ACC and braking guard: unavailable at this time. No sensor vision,” with fault code C110BF0 (adaptive cruise control sensor restricted view) stored in the distance regulation control module.
- Collision warning or braking assistance messages that say the system is restricted or unavailable.
- ACC that brakes for vehicles in the next lane, or reacts late to the car in front, which can point to a misaligned sensor.
- Faults that appear after a minor front-end bump, a parking knock, a bumper repair or a wheel alignment.
The exact wording varies by model and year, so read the message in full and look up its meaning in your owner’s manual.
Common causes: check these before you replace the sensor
An Audi technical service bulletin for the 2012–2016 A6 and A7, the 2011–2016 A8 and the 2014–2016 A3 explains that ACC switches off when a radar sensor sees no objects for an extended time. Audi lists these causes:
- Snow, ice, leaves, strong water spray, road salt or dirt over the sensor area. Cleaning it restores the system.
- A minor collision that pulls the sensor out of its plastic mounting clips without visible outside damage, which skews its view. Audi’s fix is a clip repair kit and a recalibration.
- Long tunnels, where reflections off the walls confuse the radar, and empty roads with no traffic to reflect off. In both cases the system is working as designed.
The bulletin tells technicians to avoid replacing radar sensors unnecessarily. Other causes to rule out are water or corrosion in the connector, damaged wiring after a bumper repair, and a repainted or repaired bumper cover in front of the sensor, which can weaken the radar signal.
How to diagnose it
- Clean the bumper area in front of the sensor gently, then drive on a road with traffic. If the message clears and stays away, the sensor was blocked.
- Read the fault memory with an Audi-capable scan tool. On the C7 cars, check both the main ACC module and the second radar. A restricted-view fault differs from a sensor hardware or communication fault.
- Look behind the bumper for a sensor that has moved, broken mounting clips or a cracked bracket, especially after any front-end contact.
- Check the connector and harness for water, green corrosion or chafing.
- If the sensor reports an internal fault or will not communicate, and the power, ground and wiring test good, the sensor itself is likely at fault.
Matching the part: OEM number and VIN
Radar sensors differ by model, side, equipment and software version. Read the label on your old sensor and check the number against your VIN in an Audi parts catalog. The numbers we list:
- 4G0907561 (4G0 907 561, also sold as 4G0907561A) is the right-hand, main radar listed for the C7 A6, A6 quattro, A7, S6, S7 and RS7.
- 4G0907541 (4G0 907 541, also sold as 4G0907541B) is the left-hand radar listed for the same C7 range. It is not a substitute for the right-hand unit.
- 5WA907561 (5WA 907 561) is the front ACC radar listed for the 8Y A3, A3 quattro, S3 and RS3 of 2022–2025.
See all ACC sensors or the Audi catalog. Suffix letters often reflect software or hardware versions, so match your old label.
Replacement, calibration and safety
Taking the sensor out is a modest mechanical job, often through the lower grille or with the bumper cover removed. What makes this a shop job is everything after that. A new or refitted radar has to be coded to the car and calibrated, and calibration is a requirement, not an option.
- Audi’s procedure uses a setting device with a reflector placed at a set distance in front of the car, lined up with the car’s thrust axis using wheel alignment equipment, and a diagnostic tool that runs the calibration routine. A dealer or an ADAS-capable shop has this equipment.
- The procedure includes a wheel alignment check if one has not been done, because the radar is aimed along the line the rear wheels set.
- Recalibration is also needed after the sensor or its bracket has been removed or knocked, and it is commonly checked after a wheel alignment or front-end repair.
- Until calibration is complete, do not rely on ACC or collision warning. A misaimed radar can miss the vehicle ahead or react to cars in other lanes.
- Disconnect the battery before unplugging the sensor, and handle the unit by its housing. Do not mark or paint the lens face.


